How to Place Steel Reinforcing in a Concrete Floor Slab

8 Simple steps to throw your concrete slab

Building a strong and durable concrete floor slab is essential for any construction project, whether it’s for a residential home, a commercial building, or an industrial site. Steel reinforcing plays a crucial role in providing additional strength to the concrete, ensuring it can withstand the loads and stresses it will face over time. This guide will walk you through the process of placing steel reinforcing in a concrete floor slab, including the recommended materials, techniques, and specifications.

1. Preparation of the Ground

Before placing the steel reinforcing, it’s important to prepare the ground properly. The ground should be leveled and compacted to create a stable base for the concrete slab. If necessary, remove any loose soil, organic material, or debris that could affect the slab’s stability. After leveling, it’s advisable to lay a heavy grade damp proof course (DPC) plastic sheeting over the ground. This plastic sheeting acts as a moisture barrier, preventing water from seeping up into the slab from the ground, which could weaken the concrete over time.

2. Choosing the Right Steel Reinforcing

The type of steel reinforcing you choose will depend on the size and purpose of the slab. For most standard residential or light commercial floor slabs, a typical reinforcing mesh or rebar is suitable. Here are the recommended materials:

• Reinforcing Mesh: A common choice for residential slabs is a welded wire mesh with a diameter of 6mm to 10mm. The mesh should have a grid size of 150mm x 150mm. This mesh is easy to handle and provides uniform reinforcement throughout the slab.
• Reinforcing Bars (Rebar): For heavier loads or larger slabs, use rebar with a diameter of 10mm to 16mm. Rebar should be placed in both directions, creating a grid pattern that provides support in all directions. The spacing between the rebars should typically be 200mm to 300mm, depending on the load requirements.

3. Placing the Steel Reinforcing

Once you have selected the appropriate reinforcing material, it’s time to place it in the slab:

• Spacing: For a standard residential slab, place the steel reinforcing mesh or rebar at 150mm to 200mm intervals across the entire area of the slab. If using rebar, it should be laid out in a grid pattern, with bars running perpendicular to each other. The spacing between the rebars should be consistent and should match the load requirements.
• Height Above Ground Level: The reinforcing steel should be placed at the correct height within the slab to ensure maximum effectiveness. For a typical floor slab with a thickness of 100mm to 150mm, the steel should be positioned about 50mm above the ground level. This placement ensures that the steel is embedded in the middle of the slab, where it can best resist tensile stresses.
• Support Chairs: Use plastic or steel chairs to hold the reinforcing steel at the correct height. These chairs are spaced every 600mm to 1000mm along the length of the slab, ensuring that the reinforcing remains in the proper position during the pouring of the concrete.

4. Mixing the Concrete

The strength of your concrete floor slab is directly related to the quality of the concrete mix. Here’s a standard mix for a floor slab:

• Concrete Strength: A typical floor slab mix is 25 MPa (megapascals). This strength is suitable for most residential and light commercial applications.
• Mix Proportions: The standard mix ratio for a 25 MPa concrete is 1 part cement, 2 parts sand, and 3 parts aggregate (stone). Water should be added gradually to achieve a workable consistency without making the mix too wet, which can weaken the final product.
• Materials:
  • Cement: Use high-quality Portland cement.
  • Sand: The sand should be clean and free of impurities. Medium-grade sand is ideal.
  • Aggregate: Use crushed stone or gravel with a size of about 19mm. Ensure the aggregate is clean and well-graded.
  • Water: Clean, potable water is essential for mixing. The amount of water used should be just enough to achieve a workable consistency. A water-cement ratio of 0.5 (by weight) is usually recommended.

5. Pouring the Concrete

Once the steel reinforcing is in place and the concrete mix is ready, you can begin pouring the concrete:

• Pouring: Start at one end of the slab and work your way across, ensuring that the concrete is poured evenly over the reinforcing steel. Use a shovel or rake to spread the concrete and fill any gaps around the steel.
• Compacting: After pouring, the concrete should be compacted to remove any air pockets. This can be done using a mechanical vibrator or a hand tamper. Proper compaction ensures that the concrete fully encapsulates the reinforcing steel and eliminates voids that could weaken the slab.
• Levelling: Use a straight edge or screed to level the surface of the concrete. This ensures a smooth, even surface that will be easier to finish and will provide a solid base for flooring or other finishes.

6. Curing the Concrete

Curing is a critical step in the concrete construction process, as it allows the concrete to achieve its full strength:

• Curing Time: The concrete should be kept moist for at least 7 days after pouring to ensure proper curing. Cover the slab with a plastic sheet or wet burlap to retain moisture. If the weather is particularly hot or dry, you may need to sprinkle water on the slab periodically.
• Avoiding Cracks: Proper curing helps prevent the slab from drying out too quickly, which can lead to cracking. Cracks can also be minimized by cutting control joints in the slab. These joints should be cut at a depth of about one-third of the slab’s thickness, at intervals of 2m to 3m.

7. Additional Security Measures

For slabs in high-load areas or those that will support heavy equipment, additional measures can be taken:

• Double Layer Reinforcement: In some cases, it may be necessary to use a double layer of reinforcing steel, with one layer near the top of the slab and one near the bottom. This provides extra strength and helps distribute loads more evenly.
• Thicker Slabs: For areas with particularly heavy loads, consider increasing the thickness of the slab to 150mm or more. This will provide additional support and help prevent cracking.
• Higher Strength Concrete: In situations where the slab will be subjected to extreme loads or conditions, you may need to use a higher strength concrete mix, such as 30 MPa or 35 MPa.

8. Finishing the Slab

After the concrete has been poured and leveled, it’s time to finish the surface:

• Troweling: For a smooth finish, use a steel trowel to create a hard, dense surface. This is typically done after the concrete has begun to set but is still workable.
• Textured Finish: If a non-slip surface is required, consider using a broom to create a textured finish. This is often used in outdoor slabs or areas where water may be present.
• Sealing: Once the concrete has fully cured, you may want to apply a concrete sealer to protect the surface from moisture, stains, and wear. This is especially important for slabs that will be exposed to the elements or heavy traffic.

Placing steel reinforcing in a concrete floor slab is a crucial step in ensuring the strength and durability of the slab. By carefully selecting the right materials, following proper installation techniques, and using a quality concrete mix, you can create a slab that will stand the test of time. Remember to always follow best practices for curing and finishing to achieve the best possible results. Whether you’re building a simple residential slab or a more complex commercial project, the guidelines outlined in this article will help you achieve success.

This guide should give you a solid foundation for constructing a reinforced concrete floor slab, with all the necessary details to ensure quality and durability.